• 03-03-2015, 08:53 AM
    Sherwin
    Cerwin Vega D-9 speakers ohms?- Correct ohm settings on my Pioneer spec 2 amp 4 or 8?
    I have a set of Cerwin Vega D9 speakers (1990) that I want to hook up to my Pioneer spec system, Spec2 Amp. The amp has settings for either 4ohm or 8ohm on rear of amp. I have done research on the PC and see a-lot of forums state they are powered by 4ohms but other CV charts show them as 8ohm speakers? I am a tad confused and do not want to harm the speakers or my amp by doing any false trial and errors. Anyone have any more knowledge on this please?:confused5:
  • 03-03-2015, 09:37 AM
    Hyfi
    MODEL D-9

    DESCRIPTION: 15” 3-WAY LOUDSPEAKER

    FREQUENCY RESPONSE: 29 Hz –20 kHz
    POWER HANDLING: 5/350 Watts RMS Min/Max
    SENSITIVITY: 101 dB (1 Watt @ 1 Meter)
    IMPEDANCE: 4 Ohms
    LF DRIVER: 15” Die-cast Frame / 2” Voice-Coil (152WR)
    MF DRIVER (upper): 6” Cone (M-6 or CM-6)
    MF DRIVER (lower): 6” Cone (M6-H or CMR-H)
    HF DRIVER: 1” Voice-Coil Horn Tweeter (CS-5)
    PROTECTION: Circuit Breaker (Tweeter)/Fuse (Overall)
    LEVEL CONTROLS: Tweeter & Midrange
    CROSSOVER POINTS: 500/3500 Hz.
    DIMENSIONS: 35” X 18” X 17.75” ( H X W X D )


    Question #2: My receiver is 8 ohms but your speakers are rated at 4 ohms. Is there a problem?
    Answer: The 4-ohm impedance rating on some of our speakers refers to nominal impedance meaning literally “in name only”. Since a speaker’s actual AC impedance varies depending on the frequency of the input signal, its nominal impedance refers to the impedance or resistance at only one point along the frequency curve. Cerwin-Vega’s nominal impedance rating refers only to the lowest point of the impedance curve which immediately follows its resonant peak. In order to establish this rating, Cerwin-Vega does a sine wave sweep encompassing the entire frequency band and rates the impedance as described above.

    When tested, an amplifier is usually driven with a 1 kHz sine wave into an 8-ohm load for 6 to 8 hours without overheating or exceeding its rated distortion levels. This is a very strenuous test and in the real world of normal listening, is the equivalent to playing music at full volume for 6 to 8 hours.

    A recent magazine article stated, “. . . if your receiver handled 8 ohms during the UL test, it should handle lower impedance loads under less strenuous conditions at home.” The article went on to say, “. . . a name brand, component grade [stereo amplifier/receiver] will comfortably handle a pair of 4 ohm speakers.”
  • 03-03-2015, 10:05 AM
    Sherwin
    1 Attachment(s)
    I seen this thread also but attached is a sheet that says its an 8 ohm speaker but others state it is a 4ohm (see attached). i need to know from someone that truly knows so that i do not do any damage based from magazine articles and hypothetical analysis. I prefer to run on 4ohms if i can...
  • 03-03-2015, 10:08 AM
    Hyfi
    I would suggest you ask over at AudioKarma site, where the members are Vintage nuts for the most part.
  • 03-03-2015, 10:11 AM
    Sherwin
    I will try that also. Thank you so very much for all replies :-)
  • 03-03-2015, 10:13 AM
    Hyfi
    There is actually a current thread over there about a CL pair up for sale for $50

    Cerwin Vega D9 - AudioKarma.org Home Audio Stereo Discussion Forums
  • 03-03-2015, 10:28 AM
    Sherwin
    yes, i seen. it still does not answer my main concern. I will keep searching. again, thank you so very much for all the replies :-)
  • 03-03-2015, 10:44 AM
    Hyfi
    Join and ask there if not already a member, those guys know their old gear like nowhere else.
  • 03-03-2015, 06:00 PM
    Mr Peabody
    If your amp is set to 4 ohms it will be fine, even if the CV's are 8 ohms. 4 ohms means the amp will produce a bit more current which I'd prefer anyway. This would be safer than setting the amp to 8 ohms and finding the speakers are 4 ohms. A lower impedance than the amp can handle is not good, hopefully the amp has protection and n foul, but driving a higher impedance speaker is no issue.
  • 03-04-2015, 04:56 AM
    Feanor
    Quote:

    Originally Posted by Mr Peabody View Post
    If your amp is set to 4 ohms it will be fine, even if the CV's are 8 ohms. 4 ohms means the amp will produce a bit more current which I'd prefer anyway. This would be safer than setting the amp to 8 ohms and finding the speakers are 4 ohms. A lower impedance than the amp can handle is not good, hopefully the amp has protection and n foul, but driving a higher impedance speaker is no issue.

    This is the best advice if the impedance ratung is unclear. I agree that attaching to the 4 ohm taps is safer; it might trade a bit of power output in favor of current capacity but that won't be a problem with Cerwin speakers.
  • 03-06-2015, 02:40 PM
    Sherwin
    Thank you so very much everyone, this does help.