Results 1 to 4 of 4
  1. #1
    Forum Regular Radials Rule's Avatar
    Join Date
    Feb 2008
    Location
    Louisville, KY
    Posts
    10

    Better to Just leave Power On When not in Use?

    Forgive me if this has been beaten to death. I used the search feature and came up with nothing.

    Is it better to leave my equipment on all the time or is it easier on everything to cycle them on and off every day/every couple of days.

    Even more specifically; Is there any reason that it might depend on the equipment....whether it is an amp, pre amp, cd player etc.?
    Sansui SPX8000 Speakers
    Rotel RA-972 Integrated Amp used as a preamp
    Rotel RB-1080 Amp
    Onkyo DX-702 CD Player
    MGA ML 2200 Turntable

    Top 5 (subject to rotation)
    Hector Berlioz
    Ottorino Respighi
    Aaron Copland
    Scot Ray Quintet
    Suzanne Vega

  2. #2
    Super Moderator Site Moderator JohnMichael's Avatar
    Join Date
    Apr 2005
    Location
    Central Ohio
    Posts
    6,307
    I have always heard that leaving solid state electronics on all the time is best. The thought being that turning a component on and the power surging through puts more stress than leaving it on all the time. Several of my components have standby feature instead of off so I put components in standby when I leave. I had a Rotel int. amp that was about 10 years old and it was turned on and off so I do not think with modern well designed electronics it matters. Leaving components on all the time can increase your electrical bill.
    JohnMichael
    Vinyl Rega Planar 2, Incognito rewire, Deepgroove subplatter, ceramic bearing, Michell Technoweight, Rega 24V motor, TTPSU, FunkFirm Achroplat platter, Michael Lim top and bottom braces, 2 Rega feet and one RDC cones. Grado Sonata, Moon 110 LP phono.
    Digital
    Sony SCD-XA5400ES SACD/cd SID mat, Marantz SA 8001
    Int. Amp Krell S-300i
    Speaker
    Monitor Audio RS6
    Cables
    AQ SPKR and AQ XLR and IC

  3. #3
    Shostakovich fan Feanor's Avatar
    Join Date
    Jun 2002
    Location
    London, Ontario
    Posts
    8,127

    Tubes, etc.

    Quote Originally Posted by Radials Rule
    Forgive me if this has been beaten to death. I used the search feature and came up with nothing.

    Is it better to leave my equipment on all the time or is it easier on everything to cycle them on and off every day/every couple of days.

    Even more specifically; Is there any reason that it might depend on the equipment....whether it is an amp, pre amp, cd player etc.?
    Unless my s/s component has a stand-by circuit, I turn it off. My power amps, for example, don't have stand-by, also they are a high-bias design that draws enough current at idle to be noticably warm.

    My tube preamp has stand-by which I used unless I'm away for at least a couple of days. The stand-by puts a much reduced voltage across the tubes to keep them slightly warm. It's obvious some electricity is being wasted, however (1) it takes much less time to get to good sound when the unit is fully power, (still take about 15 minutes) and (2) it avoids the "shock" to the tubes of a cold power-on which on balance might actually extend the life of the tubes.

  4. #4
    Suspended
    Join Date
    Oct 2005
    Posts
    928
    Quote Originally Posted by Feanor
    Unless my s/s component has a stand-by circuit, I turn it off. My power amps, for example, don't have stand-by, also they are a high-bias design that draws enough current at idle to be noticably warm.

    My tube preamp has stand-by which I used unless I'm away for at least a couple of days. The stand-by puts a much reduced voltage across the tubes to keep them slightly warm. It's obvious some electricity is being wasted, however (1) it takes much less time to get to good sound when the unit is fully power, (still take about 15 minutes) and (2) it avoids the "shock" to the tubes of a cold power-on which on balance might actually extend the life of the tubes.
    With your list of hardware your amps could serve a dual purpose in winter, audio and heating. I don't think the surge would hurt internal components since the first few cycles would charge the capacitors in the power supply. There usually a lot of capacitors in high-end gear. There may be some concern the power switch could go bad, which can be costly to repair. With so much emphasis on being "green", it almost be a crime to leave amps on, especially Class A. I never keep any of my hardware on and I have gear which is over 20 years old. I see no advantage except instant gratification when you're ready to listen.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •