General Setup Question [Archive] - Audio & Video Forums

PDA

View Full Version : General Setup Question



lildanbassman
08-29-2006, 02:33 PM
I just had a basic question about setup and maybe the best way to explain is just to give the scenario I'm looking at:

I'm installing a 5.1 system. The surround speakers & subwoofer are specified at 80-100W RMS and 100-130W Max. I'm currently looking at a 600W receiver with 6.1 support (100W x 6 RMS +0.5%). Am I correct in thinking that this would be ok to power all my speakers and my subwoofer (the sub is passive)? It seems good on paper but I'm not 100% sure how that works. What would happen if I installed a 1000W receiver?

fyi-the receiver I am looking at is a Kenwood VRS-n8100. It has built in ethernet support which is the main perk, but also the fact that it seems compatable with my setup. Any thoughts on it as well would be appreciated!

Sorry if this seems obvious or trite, but I'm still obviously learning!

thanks!

paul_pci
08-29-2006, 03:38 PM
You should be fine, except that most av receivers today are configured for active subs.

N. Abstentia
08-29-2006, 03:47 PM
Yeah you'll be fine. That recevier will never come close to 100x6 in reality, it will do maybe 40 watts per channel and you won't even use all that. Before you go out and buy a '1000 watt' receiver you probably need to read more and learn about real world power ratings.

And like Paul said, you don't use the receiver to power the subwoofer. It needs its own amp.

Mr Peabody
08-29-2006, 07:20 PM
In addition, it's always better to drive your speakers with too much power than not enough. Clipping, or overdriving, your amp will kill far more speakers than having too much power.

lildanbassman
08-30-2006, 05:50 AM
Yeah you'll be fine. That recevier will never come close to 100x6 in reality, it will do maybe 40 watts per channel and you won't even use all that. Before you go out and buy a '1000 watt' receiver you probably need to read more and learn about real world power ratings.

I think you are really hitting on what my question is. I guess I assumed that if its a 600 watt amp, it will be putting out 600 watts continuously. I'm not sure how it regulates or "knows" how to adjust wattage for each channel. I think what I really need is a good article on this to look over and read. I've tried to scour the internet but I haven't found one. Know any off the top of your heads?

thanks for all your replies! :)

paul_pci
08-30-2006, 09:20 AM
Go to www.audioholics.com and browse through their links on learning different formats and meaurments. They're pretty obssessive over there about debunking audio myths and popular conceptions of equipment that just don't hold true.

Mr Peabody
08-30-2006, 05:12 PM
If an amp is rated at X watts per channel, whether it has 2, 5, or 6, it will only do X watts to each speaker hook up.

Another place to get good beginner information is www.crutchfield.com they are a very good on line retailer but their website is full of articles and information on a variety of home and auto electronics.

likeitloud
08-31-2006, 03:17 AM
The company rates the amp in the receiver a certain number, but is not under "load".
By the time it's driving 5/6/7 speakers, you maybe have a 3rd of the power, thats
actually being used, it goes thru all the electronics in the chassis, the wire, the drivers
so if anything it's not overpower issues, it's clipping issues, or underdriving your
speakers, that cause damage. Unless you go really crazy with the volume, you'll
be okay. I played my 7.1 receiver to insane volumes, before adding a amp, and never
came close to overdriving the speakers or the receiver, so hook up everything and go
nuts. By the way Crutchfield Rocks. They have alot of on-line manuals available
with specific Q and A sections that have really taught me alot. Also there's are group
of about 15-20 guys on this forum who have helped out time and time again (you know
who you are). After you get comfortable with your rig, we'll get into the whole
external amp issue, which will take away all the stress if your worried about being
underpowered, Good Luck.

lildanbassman
08-31-2006, 08:12 AM
You guys are awesome! This has been a really big help. I'll be sure to check out Crutchfield and Audioholics. Thanks again!

westcott
08-31-2006, 09:50 AM
Here is the artice that I believe paul_pci was referring to.

All channel driven amplifier test (http://www.audioholics.com/techtips/audioprinciples/amplifiers/ACDTEST.php)

It should answer most of your questions.

In summary, I suggest hooking up your amp\receiver to one circuit and your powered sub to another as a minimum.

jrhymeammo
08-31-2006, 12:02 PM
This site may help you get a better receiver for your hard earned cash

http://cgi.videogon.com/cgi-bin/fs.pl?rcvr51ch

kelsci
09-01-2006, 12:40 AM
What kind of passive subwoofer do you have? Does it have input and output speaker terminals?