Speaker question URGENT

[corcaa]

I just drop (by accident) one of my Mirage AVS-200 speakers. The back part with the crossover came off with the cables and I need to know which cables go with the tweeter and which ones with the driver. I belive they have two pairs, one black and blue and the other one is red and white. Thanks for your help.

[markw]

...you could always go inside and look at the other speaker to answer this.

[corcaa]

But I don't want to force the other one. The front and back are glue to the board...

[Florian]

Well i dont think anyone of us has the schematic for that speaker so your best bet is to write Mission audio and ask for a schematic and hope they send it to you. Other then that, your only other option is to take the other one apart.

Good luck

-Flo

[N. Abstentia]

Judging by this picture:
http://images.google.com/imgres?imgurl=http://www.allacoustics.ru/image/acoustics/Mirage_AVS-200_200.jpg&imgrefurl=http://www.allacoustics.ru/shelf-speakers/Mirage/AVS-200-237.htm&h=200&w=200&sz=22&tbnid=wQHssmQkBMpOXM:&tbnh=99&tbnw=99&hl=en&start=1&prev=/images%3Fq%3DMirage%2BAVS-200%26svnum%3D10%26hl%3Den%26lr%3D%26client%3Dfire fox-a%26rls%3Dorg.mozilla:en-US:official%26sa%3DN

The front pops off just like a normal grille on any other speaker (note the 4 holes). Pop the front off the other one, remove the driver, and look at the wires.

[Pat D]

I just drop (by accident) one of my Mirage AVS-200 speakers. The back part with the crossover came off with the cables and I need to know which cables go with the tweeter and which ones with the driver. I belive they have two pairs, one black and blue and the other one is red and white. Thanks for your help.

You could contact Technical Support at Mirage.

http://miragespeakers.com/service&support.shtml

Or maybe your dealer knows.

[armyscout42]

TO CORCAA,
IF YOU HAVE PICTURES OF YOUR LOUDSPEAKERS, YOU CAN SEND IT TO MY EMAIL, I MAYBE ABLE TO FIGURE IT OUT FOR YOU...

I HAVE REPAIRED LOUDSPEAKERS BEFORE OF CONVENTIONAL DESIGN.
I ALSO HAVE A BACKGROUND IN TESTING IN ELECTRONICS, AND CLASS H AMPLIFIER BACKGROUND IN THE PAST. I AM ALSO A FORMER HIGH END HOME THEATER INSTALLER.
I HAVE SO MANY LOUDSPEAKER COLLECTIONS FROM ELECTROSTATS TO DYNAMIC TO COHERENT LINE WALSH DESIGN TO LINAEUM TWEETERS AND RIBBONS, IF I CAN BE OF HELP I WOULD LIKE TO HELP YOU.

NORMALLY WHEN YOU HAVE THAT MANY COLOR CODES, BOTH THE HIGH RANGE AND LOWER RANGE ARE SEPARATED FOR BI WIRING OR BI AMPING.
WHAT YOU MEANT BY DRIVER IS WOOFER....because a driver is a general term for speakers: you either have a tweeter, midrange or woofer as drivers which covers full range or 3 way. The purpose of the crossover is to split the frequency range into 3 distinct currents which separates them into high, mid and low audible range once it is filtered out thru the crossover's capacitors/coil....
the red wire is usually the positive that goes to the tweeter terminal and the white on this configuration to the negative terminal of the tweeter. The blue goes to the woofer's positive terminal, while the black goes to the negative terminal.

Your best bet here is to compare both speaker wiring by opening the NON DAMAGED OR BROKEN PAIR...that is the easiest way. You can always test the wires which gets a little tricky if you don't know what you are doing thru a multimeter.

Writing to the manufacturer like those in the forum suggested is your BEST OPTION!
If I had pictures of the internal component, i can be of help....simply trying to visualize from paragraphs is a little on the guessing side?

bruceleeclone@sbcglobal.net if you like me to look at it if you have pictures, otherwise, contact the manufacturer...or do the suggested recommendation by those in the forum including myself.